Whirlpool Cabrio Washer Error Codes & Repair Help
Cabrio Error Codes
LF | Ld | uL | oL | Sd | lid | Po | HC | dL | dU | F1 | F2 | F30 | F32 | F40 | F41 | F50 |
F51 | F52 | F53 | F54 | F70 | F71 | F72 | F80 | F81 | F82 | F83 | F84 | F85
Whirlpool Cabrio Washing Machines
WTW6200SW0, WTW6200SW1, WTW6200SW2, WTW6200SW3, WTW6200VW0, WTW6200VW1, WTW6300SB0, WTW6300SB1, WTW6300SB2, WTW6300SG0, WTW6300SG1, WTW6300SG2, WTW6300SW0, WTW6300SW1, WTW6300SW2, WTW6300WW0, WTW6340WW0, WTW6400SW0, WTW6400SW1, WTW6400SW2, WTW6400SW3, WTW6500WW1, WTW6600SB0, WTW6600SB1, WTW6600SB2, WTW6600SB3, WTW6600SG0, WTW6600SG1, WTW6600SG2, WTW6600SG3, WTW6600SW0, WTW6600SW1, WTW6600SW2, WTW6600SW3, WTW6700TU1, WTW6700TU2, WTW6700TW0, WTW6700TW1, WTW6700TW2, WTW6800WB1, WTW6800WL1, WTW6800WW1, WTW7300XW0, WTW7340XW0, WTW7600XW0, WTW7800XW0
NOTE: For All Cabrio Error Codes...
Write Down The Error Code! Then press PAUSE/CANCEL once to clear the error code and try to start a new cycle.
If code appears again put the washer through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea. (Watch The Cabrio Diagnostics Video) This will reveal any stored Cabrio error codes. Then you will be able to better use this repair guide to fix your Cabrio washer's major malfunction. Now put the tea down and get to work!
Cabrio LF Error Washer is taking too long to fill (Stored Error Code F30)
Check the following:
Are the water inlet hoses kinked or clogged?
Are the valve screens clean?
Are both water faucets turned on?
Do you have flood stop water supply hoses that may have closed internally?
Is the Cabrio's drain hose sticking too far into your home's drain pipe (siphoning)?
Is the pressure switch hose kinked, disconnected, or punctured?
Press PAUSE/CANCEL to clear Cabrio's display.
Cabrio Ld Error Washer is taking too long to drain water from the washtub
(Stored Error Code F32)
Check the following:
Is the Cabrio's drain hose or pump clogged?
Is the drain hose higher than 96" to reach the drainpipe?
Is the drain pump running?
Is the pressure transducer hose kinked, disconnected, or punctured?
Press PAUSE/CANCEL to clear display.
Washer Diagnostic Modes and Tests
Cabrio uL Error Unbalanced Load
If the load is unbalanced, the Cabrio washer will display this code while running an imbalanced load correction routine at the end of the wash cycle and before the final spin. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, open lid and redistribute the load. Close lid and press START.
If the washer is actually going out of balance on a regular basis and the load is similar weighted items at least half full. Then you likely need to replace the suspension spring rod kit. The New Cabrio Suspension Repair Kit comes with all 4 shocks and are common to need replacement. The new Cabrio washer suspension repair kits seem to work better and last longer than earlier versions.
Cabrio oL Error Over Loaded (Stored error Code F70)
Is the washer overloaded? The washer has attempted to fill and begin a wash cycle. If the washer is overloaded, it will drain any water and detergent that was added during the fill. To correct the overload, remove several items and add detergent. Close lid and press START.
That's how it should be perfect world where washing machines are constructed with quality materials. However, in this wasteful world of poor quality the inner tub may be jammed in the down position, unable to float off the drive hub because of a rusted drive shaft! (Removing the inner tub to clean and lubricate the shaft may help.) Or hopefully there is just a sock or something lodged in between the inner and outer baskets causing the same result.
Cabrio Washer Diagnostic Modes and Tests
Cabrio Sd Error Suds Detected (Stored Error Code F71)
Did you use regular detergent?
Regular detergents are not recommended for Cabrio washers. Use only High Efficiency ("HE") detergent.
Did you add too much detergent?
Always measure detergent and follow detergent directions. If excessive suds are detected, the washer will display this code while running a suds correction routine at the end of the wash cycle. The suds reduction routine removes extra suds and assures proper rinsing of your garments. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, re-select your desired cycle using cold water. Press START. Do not add detergent.
Cabrio lid Error Lid Opened (Stored Error Code F81)
Is the Cabrio's lid open?
Close the lid to clear the display. If the lid remains open for more than 10 minutes, water in the washtub should drain out.
Cabrio Washer Lid Lock Diagnostic Tests
Cabrio Po Error Pump Out (Lid Opened)
Po flashes when the lid of the Cabrio washing machine has been left open for more than 10 minutes. Close the lid to stop the drain pump.
Cabrio HC Error Hot & Cold Hoses Switched
This code will appear at the end of the wash cycle to indicate that the hot and cold-water inlet hoses are reversed.
If that is not the case you may need to check the washer's temperature sensor (in the Cabrio washer's water valve. Or there may be a problem with the Cabrio's main control board.
Cabrio dL Error Door/Lid Cannot Lock (Stored Error Codes F80, F82, F84, F85)
Indicates the Cabrio's lid cannot lock.
Check for items caught in the lid keeping it from closing completely.
Is soap, fabric softener, or anything else keeping the lock from extending into the lid?
The control detects an open lid switch, or cannot determine if the lid is locked. Test the lid lock connection to the washer's control board and lid lock resistance levels.
Press PAUSE/CANCEL once to clear the code.
Cabrio Washer Lid Lock Diagnostic Tests
Back to Top
More Cabrio Error Codes
